Genelec 8050 Dark Grey Front

Genelec 8050B

Genelec 8050B

Starting from £1,289.00

Active Nearfield Monitors

  • Broadcast & TV Control Rooms
  • Audio Video Post Production
  • MobileVans
  • Project/HomeStudios
  • DigitalWorkstations
  • Multimedia Production and Playback 
Normally ships 5-9 days
Only %1 left

Genelec 8050B


The Genelec 8050B is a powerful bi-amplified active monitor system with a wide frequency response and high SPL capability. The 8050B takes full advantage of the unconventional design and advanced technologies of Genelec’s 8000 Series loudspeaker range. The all- aluminium Minimum Diffraction Enclosure™ (MDE™) and advanced Directivity Control Waveguide™ (DCW™) technologies are care- fully matched with advanced ampli er and electronic circuitry and the latest driver gen- eration. Bass response extends down to an astounding 35 Hz, while distortion is extremely low due to a unique new rear reflex port design. The system's excellent directivity characteristics and accurate imaging as well as the exible mounting options make the 8050B the perfect monitoring tool for a wide range of applications.

The 8050B has been specially designed to have considerable LF extension so it can be used as main speaker for most situations. However if greater SPL's and an even lower cutoff frequency are required, it can be complemented with a Genelec subwoofer. 


Integrated construction


The 8050B is very easy to set up and use, the only connections required are the mains supply and the line level input. The input is made via a balanced female XLR connector. The input sensitivity of the 8050B can be adjusted for easy level matching with other audio equipment. The integrated design allows the amplfiers and the drivers to be calibrated as a single unit, eliminating the effects of component tolerances and ensuring consistent production quality.


Crossover Filters


The amplier unit contains an active crossover, a feature more commonly used in large and expensive control room monitors. This is the ideal method for dividing the input signal between the driver units. The active crossover allows the overall response of the system to be optimized to an extent impos- sible with a passive system. To maintain uniform frequency balance in differing acoustic environments, special calibrated controls are included in the active crossover network. These controls include “treble tilt”, “bass tilt” and “bass roll-off” functions.

A new function, “desktop low frequency” control attenuates the bass frequencies around 160 Hz by 4 dB. This feature is designed to compensate for the boost often occurring at this frequency range when the loudspeaker is placed upon a meter bridge, table or a similar re ective horizontal surface. 




The bass and treble amplifiers produce 150 and 120 watts of output power each, with very low THD and IM distortion values. Each amplifier is designed to precisely match the driver it is connected to, thus ensuring the highest subjective sound quality currently possible. The amplfier unit also contains a protection circuit that monitors the output levels and prevents any damage to the drivers. This makes the system immune to overloads and spurious signals.




A 25 mm (1") metal dome tweeter is loaded by an advanced DCW™ waveguide, which is integrated into the one piece front baffle. The improved DCW™ provides superior directivity charcteristics and perfect matching between the drivers. The 205 mm (8") bass cone driver is mounted in a newly designed bass reflex enclosure. The long, low optimized reflex tube has a large cross sectional area and terminates with a wide are at the back of the enclosure. Protective grilles are positioned in front of both drivers. Magnetic shielding is standard on the 8050B. Shielding is vital for applications such as video post production, where stray magnetic fields must be minimized.


ISS™ autostart function


When the power switch on the back panel of the loudspeaker is set to “ON”, the Intelligent Signal Sensing™ (ISS™) autostart function of the 8050B is active. Automatic powering down to standby mode happens after a certain time when playback has ended. The power consumption in standby mode is typically less than 0.5 watts. The playback will automatically resume once an input signal is detected from the source. There is a slight delay in the automatic powering up. If this is undesirable, the ISSTM function can be disabled by setting the “ISS DISABLE” switch on the back panel to “ON” position. In this mode, the monitor is powered on and off using the power switch on the back panel.


MDE™ and DCW™Technology


The Minimum Diffraction Enclosure™ (MDE™) Technology increases the performance of the Genelec 8000 Series loudspeakers by minimizing edge diffraction and improving frequency and power response. The edges of the enclosure are rounded and blend seamlessly into the enlarged Directivity Control Waveguide™. Surface discontinuities that cause diffraction are minimized. The curved walls of the die-cast aluminium enclosure are thin but rigid, allowing maximum internal volume while also providing improved EMC shielding and heat dissipation for the amplifiers. Locating the reflex port to the back of the enclosure allows a generously dimensioned reflex port for minimal port noise and excellent bass articulation while freeing the front baffle for an enlarged and optimized DCW™. The advanced DCW™ is designed to match the performance of the drivers in terms of both frequency response and directivity. This results in a smoother overall frequency response on and off axis. In addition, the improved directivity control causes more direct sound and less reflected sound to be received at the listening position, providing improved imaging and reducing the effects of room acoustics. The DCW™ improves the drive unit sensitivity by +2 to +6 dB, thus also increasing the available system maximum sound pressure level.




The 8050B offers several mounting options: The vibration insulating Isolation Positioner/ Decoupler™ (Iso-Pod™) table stand allows tilting the speaker for correct alignment of the acoustic axis. The stand can be attached to three mounting points allowing vertical and symmetrical horizontal positioning. On the rear of the enclosure there are two sets of M6x10 mm threaded holes to accommodate an Omnimount® size 60.0 bracket. On the base of the enclosure is a M10x10 mm threaded hole which can be used for securing the loudspeaker to its base




The 8050B is guaranteed for a period of two years against faults in materials or workmanship.

Need Assistance? We're Here to Help!

Personalised Product Guidance

Whether you're seeking specific details about a product, or require advice on how it integrates with your existing setup, we're readily available to assist. Our team of specialists is on hand to help you make an informed decision.

Custom Solutions and Consultation

If you're unable to find the information you need on our website, or wish to discuss custom solutions, please feel free to contact us. We provide consultation services designed to assist you in creating an ideal audio environment.

Competitive Quotations and Pricing

In addition to personalised advice, we also offer quotations for our products and services. If you're planning a project or considering a purchase and have found a better price elsewhere, let us know. We strive to offer competitive rates and will do our best to accommodate your budget. Email us your requirements and we will provide a detailed quote to help you plan your investment with clarity and confidence.

Contact Us

Email us now for tailored advice, bespoke quotations, and solutions that respect your budgetary considerations.